The Hot End and Bed Temp controls are way down at the bottom of the screen. On the Control Tab, there arent any buttons to STOP, or PAUSE the print?! It requires me clicking back to the Print Tab in order to stop the print. ![]() Why doesnt it stay at the zoom level I had before? I have to zoom all the way in again to see the model. If I click over to the Print tab, and then back to the Control tab, the view is completely "zoomed out" (ie its fitting the image of the entire bed to the preview window). Why not combine the preview screen and the control screen into one? If I dont select a file to print, and then click on the Control tab, it just shows me an empty bed. This does not match what is going on, on the printer. If I print this model, and click over to the Control window, it shows me the extrusion paths the same way, ie as if they are all converging to a single point. Thats certainly not how this model prints in reality. Where parallel lines exist in the gcode (to fill the bottom layer of the box), in the preview, over 50% of the lines converge, as if they are starting at a single point in the layer. In addition, the extrusion paths on the square box are not being shown correctly. So its not the model of my washer that is causing an issue. ![]() When I preview it, it does show me the entire box, although the surrounding skirt has been truncated to be the same/similar 1/4 (upper right). I uploaded another simple model, a rectangular calibration box. Looked at every setting in the interface, and I dont see anything which will change this. Is there something in the software which is somehow limiting the amount of the gcode being displayed? Also, if I move the percentage dial, it thinks the model starts at the black dot (which is incorrect). Also, I now see the first layer gcode, EXCEPT I only see the upper right corner of the model/print (like your software cut a 1/4 pie slice out of the gcode)?! The other 3/4s of it is simply not there. If I click "+" next to Layer, it shows me Z position of 0.2mm for layer 2 (which is about right). ![]() In the actual model preview window, it only shows me a black dot in the lower left corner, and one green line going up and to the right at a 45 degree angle (which appears to be a move), and nothing else. In the Preview Window, it says the Z Position of layer 1 is 320mm (incorrect). I uploaded a simple, small gcode file of an 80mm diameter washer (sliced in Kiss, its only 460kB). I defined the Z-Max and Z-Home Position in printer settings to be 320mm. I do have some issues with the Server software though, now that I have it installed and working: I even found/followed the instructions (on this site) for how to set up the camera, and that works great, although it took some Googling/Youtubing in order to find those instructions. So I went in search of another package for the Pi, and came across Repetier Server (I didnt know about it, only the Host). I also heard about Octoprint, so I installed that on the Pi. I heard about the new Raspberry Pi 2, so I ordered one, along with the Pi camera. Ive really been wanting to offload the actual printing to another system, somehow. Ive been using Repetier Host on my CAD system (which is great btw). So I am out of ideas to create a workarround :-) It tried to run the server with the logged in user instead the system user but nothing changed. So it looks like the repetier server is ignoring the backslash's !? Simply add any command he needs to hack your system.Ĭ:\Windows\System32\shutdown.exe /s /m \\localhost /t 3200 If you would allow online configuration, a hacker could The commands you enter here are executed with the privileges of theĭaemon running the server. Security consideration: The reason there is no online editor for this is simply 16:07:46: Handling action runExternalCommand caused error System exception 16:07:33: New session: 16:07:46: Starting external command c:Windowsnotepad.exe with 0 parameters. The problem is that no of my created commands are working an in the server.log it says the following: Like discribed in the manual I created the extcommands.xml file and stored it in C:\ProgramData\Repetier-Server\databaseĪfter restarting the repetier server service the new commands appeared in the menu - ok until here.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |